The Option column of the table shows the name of the system command that displays the status of that option.
The Default column of the table shows the system command that reestablishes the default setting. For some options, such as OP and PLI, you must use two or more system commands to establish the default setting. For some options, the phrase (Dependent on code) appears, where code is one of the following values:
-
(blank)
The default value listed in the Default column is established by a LOADER cold-start run.
-
LOADER
The default value listed in the Default column is established by a LOADER cold-start run unless you give the LOADER a command to set the option to a specific value.
-
JOBDESC
The default value listed in the Default column is established every time that the CONTROLLER (at halt/load time) creates a new JOBDESC file on the DL JOBS family. The CONTROLLER creates a new JOBDESC file for any of the following reasons:
-
Either the system or LOADER changed the DL JOBS setting to reference a disk family that does not have a JOBDESC file.
-
The system executed a ??RJ primitive command for the old JOBDESC file.
-
An error occurred when the old JOBDESC file was set up.
-
-
CONFIGURATION
The values for these options are established either by the configuration file used by a RECONFIGURE GROUP command or by LOADER.
-
PRINTERINFO
PRINTSUPPORT establishes these default values whenever the PRINTSUPPORT library starts. This library creates a new SYSTEM/PRINTERINFO file.
|
Option |
Default |
|---|---|
|
ACCOUNTING |
ACCOUNTING DEPENDENTTASK IDENTIFIED. ACCOUNTING FILE IDENTIFIED Refer to ACCOUNTING (Resource Accounting) |
|
ADM |
ADM (ACTIVE 7, WAITING 3, SCHEDULED 2, COMPLETED 5, MESSAGES) DELAY 9 (Dependent on JOBDESC) Refer to ADM (Automatic Display Mode) |
|
AI |
No automatic initiation programs Refer to AI (Automatic Initiation) |
|
ASD |
ASD 50 Refer to ASD (Actual Segment Descriptor) |
|
AUTORESTORE |
DONTCARE Refer to AUTORESTORE (Archiving AUTORESTORE Option) |
|
BNA |
INIT/INFO file = *NULL. Next INIT/INFO file = *NULL Refer to BNA |
|
BNAVERSION |
BNAV2 Refer to BNAVERSION |
|
CF |
CF (Dependent on LOADER) Refer to CF (Configuration File) |
|
CM |
CM <MCP name> (halt/load unit index) HLDUMPDISK STANDBY (Dependent on LOADER) Refer to CM (Change MCP) |
|
CO |
CO -BINARYPREFIXES, -ERRORDP, - INPUT, - MONITOR, - SPRWARN, - SEPARATEMSGS , - COMPACTSQ, - TRACE (Dependent on JOBDESC) Refer to CO (CONTROLLER Options) |
|
COMPILERTARGET |
COMPILERTARGET THIS Refer to COMPILERTARGET (Set Default Target Value) |
|
CS |
CS Refer to CS (Change Supervisor) |
|
DL |
DL BACKUP <halt/load family>, DL CATALOG (has no default), DL DPFILES, DL JOBS <halt/load family>, DL OVERLAY 504 <halt/load family>, DL ROOT, DL SORT DISK, DL USERDATA <halt/load family> (Dependent on CONFIGURATION, LOADER) Refer to DL (Disk Location) |
|
DN |
DN Refer to DN (Dump Name) |
|
DO |
All options are RESET |
|
DQ |
DQ 0 (Dependent on JOBDESC) Refer to DQ (Default Queue) |
|
DRC |
DRC Refer to DRC (Disk Resource Control) |
|
FILELOCKTLIMIT |
FILELOCKTLIMIT 0 Refer to FILELOCKTLIMIT (File Lock Time Limit) |
|
HLUNIT |
The disk from which the system was most recently halt/loaded (Dependent on LOADER, CONFIGURATION) Refer to HLUNIT (Specify Halt/Load Unit) |
|
HOSTNAME |
HN (Dependent on CONFIGURATION) Refer to HOSTNAME (Hostname) |
|
HS |
HS Refer to HS (Hold Schedule) |
|
HU |
HU Refer to HU (Host Usercode) |
|
ID |
ID SYSTEM: MAXPSEUDO 0 Refer to ID (Initialize Data Comm) |
|
LICENSESTATUS |
LICENSESTATUS TEMP WARNFACTOR – Refer to LICENSESTATUS |
|
LOGGING |
LOGGING DEFAULT Refer to LOGGING (Logging Options) |
|
MAX |
MAX MESSAGES 500, MAX COMPLETED 500, MAX SESSION 9999 Refer to MAX (Maximums) |
|
MIRROR OPTION |
MIRROR OPTION PARTIALSETS WAIT MIRROR OPTION QUICKAUDIT OFF Refer to MIRROR (Mirror Disk) |
|
MDT |
MDT COMPLETE Refer to MDT (Memory Dump Type) |
|
MIXLIMIT |
MIXLIMIT (Dependent on JOBDESC) Refer to ML (Mix Limit) |
|
MSC |
MSC CLEAR Refer to MSC (Message Control) |
|
MQ |
MQ 0, MIXLIMIT 10, DEFAULTS (PRIORITY = 50), LIMITS (PRIORITY = 99) (Dependent on JOBDESC) Refer to MQ (Make or Modify Queue) |
|
NET |
NET = *NULL Refer to NET (Network) |
|
OP |
OP + TERMINATE, LPBDONLY AUTORM AUTORECOVERY MOREBACKUPFILES or OP + 2, 4, 5, 8, 25. (Dependent on LOADER) Refer to OP (Options) |
|
OPLOCKTIMEOUT |
OPLOCKTIMEOUT = 30,10 Refer to OPLOCKTIMEOUT |
|
PLI |
PLI 60 PLI Refer to PLI (Periodic Logging Interval) |
|
PS ACTIVE |
PS ACTIVE BNA PS ACTIVE REMOTE PS ACTIVE SITE = 0 (Dependent on PRINTERINFO) Refer to PS ACTIVE |
|
PS ASSOCIATE |
PS ASSOCIATE<device specifier> (Dependent on PRINTERINFO) Refer to PS ASSOCIATE |
|
PS BANNER |
PS BANNER PAGECOMP (Dependent on PRINTERINFO) Refer to PS BANNER |
|
PS CONFIG |
PS CONFIG + <all line printers> (Dependent on PRINTERINFO) Refer to PS CONFIGURE |
|
PS DEFAULT |
PS DEFAULT COMPRESSFILES = FALSE, CONFIGURE = AUTOMATIC, DESTINATION (unspecifieddefault pool), JOBSUMMARY = UNCONDITIONAL, PRINTDISPOSITION = EOJ, REMOVEDLOCKED = NEVER, PRINTERKIND = DONTCARE, REQUESTMAX = 9999999, SHOWDISPLAY = UNSORTED (Dependent on PRINTERINFO) Refer to PS DEFAULT |
|
PS DEFAULT JOBSUMMARY |
PS DEFAULT JOBSUMMARY = UNCONDITIONAL Refer to PS DEFAULT |
|
PS FONTLIB |
PS FONTLIB <PRINTERKIND value> (Dependent on PRINTERINFO) Refer to PS FONTLIB |
|
PS GROUP |
PS GROUP <group name> (Dependent on PRINTERINFO) Refer to PS GROUP |
|
PS HEADER |
PS HEADER (Dependent on PRINTERINFO) Refer to PS HEADER |
|
PS SELECTION |
PS SELECTION criterion 1: volume (Dependent on PRINTERINFO) Refer to PS SELECTION |
|
PS TRAILER |
PS TRAILER (Dependent on PRINTERINFO) Refer to PS TRAILER |
|
REMOTESPO : OK |
No authorized REMOTESPO stations Refer to REMOTESPO (Activate REMOTESPO) |
|
RESTRICT COMMAND |
No restricted commands Refer to RESTRICT (Set Restrictions) |
|
SB |
SB DISK = DLBACKUP, PACK = PACK, TAPE = TAPE Refer to SB (Substitute Backup) |
|
SBP |
SBP INTERVAL = 10, SLICERATE = 50, CPURATE = 20, SCHEDULING = BYGLOBAL Refer to SBP (System Balancing Parameters) |
|
SECOPT |
SECOPT CLASS U Refer to SECOPT (Security Options) |
|
SEGARRAYSTART |
MAX(65536, PAGE_SIZE) where PAGE_SIZE is set by the CPM firmware. (Dependent on CONFIGURATION) Refer to SEGARRAYSTART (Array Segmentation Start Size) |
|
SF |
SF OLAYGOAL 0, AVAILMIN 0, FACTOR 100, OVERLAYABLEMIN 1, BUFFERGOAL 2048, OLAYSATURATION 15, OLAYCHANGE 10 (Dependent on CONFIGURATION) Refer to SF (Set Factor) |
|
SI |
No intrinsic file name Refer to SI (System Intrinsics) |
|
SL |
Establishes the following support libraries. The codefile family is the halt/load family. Refer to SL (Support Library) ATTSUPPORT = *SYSTEM/ATTSUPPORT CENTRALSUPPORT = *SYSTEM/CENTRALSUPPORT CODEFILESUPPORT = *SYSTEM/CODEFILESUPPORT COMSLANGSUPPORT = *SYSTEM/COMS/LANGUAGE/SUPPORT COMSSUPPORT = *SYSTEM/COMS COMSTTPSUPPORT = *SYSTEM/COMS/PSH/TTP CREDENTIALSUPPORT = *SYSTEM/NXSERVICES/CREDENTIALSUPPORT DATACOMSUPPORT = *SYSTEM/DATACOMSUPPORT DRCSUPPORT = *SYSTEM/DRCSUPPORT EVASUPPORT = *SYSTEM/EVASUPPORT GENERALSUPPORT = *SYSTEM/GENERALSUPPORT IP1SUPPORT = *SYSTEM/IP1SUPPORT JOBFORMATTER = *SYSTEM/JOBFORMATTER KEYEDIOIISUPPORT = *SYSTEM/KEYEDIOII LICENSESUPPORT = *SYSTEM/LICENSESUPPORT LPPSUPPORT = *SYSTEM/LPPSUPPORT MARCSUPPORT = *SYSTEM/MARC/COMMANDER MESSAGESUPPORT = *SYSTEM/MESSAGESUPPORT NETWORKSUPPORT = *SYSTEM/NETWORKSUPPORT PRINTSUPPORT = *SYSTEM/PRINT/SUPPORT SDASUPPORT = *SYSTEM/SDASUPPORT WFLSUPPORT = *SYSTEM/WFLSUPPORT VSLSUPPORT = *NAPSYSTEM/VSL |
|
STRUCTURECACHE |
STC DIRECTORY 100 STC HEADERS 30 STC CODESTACKS 15, 60 STC USERDATAFILE 200 Refer to STRUCTURECACHE (Cache Maintenance) |
|
SUPPRESSWARNING |
SUPPRESSWARNING NONE Refer to SUPPRESSWARNING (Suppress Warning) |
|
SYSOPS |
SYSOPS CATALOGLEVELSET = RESET CCSVERSION = ASERIESNATIVE CONVENTION = ASERIESNATIVE DATEWARN = RESET DIRECTPRINTER = RESET ESR = CONDITIONAL LABELFORMAT = ANSI69DEFAULT LANGUAGE = ENGLISH LMBLOCKSIZE = 0 LONGFILENAMES = RESET* PERMDIRECTORIES = RESET QUEUEDAX = RESET RCBP = RESET RSVPONTAPEERROR = RESET SYSTEMDIRECTORY = RESET TAPEOVERWRITE = RESET TAPESERVER = RESET TAPEMANAGER = RESET TAPEEXPIRATION = TRUE WARNFACTOR = STANDARD WRAPNOWAIT = RESET *This option is unique because LOADER always prompts the operator for the desired value of the parameter during a cold-start. If during a halt/load the DL CATALOG family is determined to contain a usable file access structure that is in the long file name format, the MCP unconditionally sets the LONGFILENAMES option. Refer to SYSOPS (System Options) |
|
TERM |
TERM LINES 24, WIDTH 80, FIRST 2, TRUNCATED TRUE, RESPONSE EXPANDED, MESSAGES FALSE (Dependent on JOBDESC) Refer to TERM (Terminal) |
|
TL |
TL ROWS 140 RECORDS 1000 Refer to TL (Transfer Log) |
|
UQ |
UQ <device type> <unit number list> (Dependent on JOBDESC) Refer to UQ (Unit Queue) |
|
??SECAD |
??SECAD Refer to ??SECAD (Security Administrator Authorization) |
